BS EN 60603-13-1998 印制电路板用频率低于3MHz的连接器.不易卸绝缘可置换终端用带独立连接器的2.54mm(0.1in)基本网格印制板用经质量评定的两对端连接器详细规范

作者:标准资料网时间:2024-05-02 06:35:54 浏览:9250 来源:标准资料网

【英文标准名称】:Connectorsforfrequenciesbelow3MHzforusewithprintedboards-Detailspecificationfortwo-partconnectorsofassessedquality,forprintedboardsforbasicgridof2,54mm(0,1in)withfreeconnectorsfornon-accessibleinsulationdisplacementte
【原文标准名称】:印制电路板用频率低于3MHz的连接器.不易卸绝缘可置换终端用带独立连接器的2.54mm(0.1in)基本网格印制板用经质量评定的两对端连接器详细规范
【标准号】:BSEN60603-13-1998
【标准状态】:现行
【国别】:英国
【发布日期】:1998-05-15
【实施或试行日期】:1998-05-15
【发布单位】:英国标准学会(BSI)
【起草单位】:BSI
【标准类型】:()
【标准水平】:()
【中文主题词】:名称与符号;腐蚀试验;接线端;电连接器;座椅;检验;评估的质量;漏电路径;电气试验;资格鉴定;尺寸;量规;认可试验;低频;电流;详细规范;质量保证体系;质量评估;印制电路;规范(验收);印制电路板;固定的;振动
【英文主题词】:Blade-clampingconnections;Connectoredjoints;Detailspecification;Electricplugs;Electronicequipmentandcomponents;Indirect;Insulationdisplacementtechnique;Printedcircuits;Quality;Specification
【摘要】:ThispartofIEC603coversarangeoftwo-partconnectorswithcontactarrangementshavingspacingsof2,54mm(0,1in)inbothdirections.Thetwo-partconnectorrangecomprisesafixed(board-mounted)connectorcontainingmalecontactsandafreeconnectorcontainingfemalecontacts.Theyareprimarilyintendedtoprovideinterconnectionbetweenprintedboardsusingabasicgridof2,54mm(0,1in)aslaiddowninIEC97androundconductorribboncableon1,27mm(0,05in)centrelinespacing.Thefixedconnectorsareprovidedwithpostseitherforsolder,press-inorwrappedconnections.Thefreeconnectorsareprovidedwithnon-accessibleinsulationdisplacementterminations.
【中国标准分类号】:L30
【国际标准分类号】:31_220_10
【页数】:48P.;A4
【正文语种】:英语

下载地址: 点击此处下载

返回跳至顶部

上一篇: BS IEC 61000-5-2-1998 电磁兼容性.安装和缓解指南.接地和电缆敷设
下一篇: BS Z 7-1998 空间数据和信息传输系统.ASCII编码英语

基本信息

标准名称：	数字会议电话主席控制盘技术要求
中标分类：	通信、广播 >> 通信设备 >> 电话通信设备
发布部门：	中华人民共和国铁道部
发布日期：	2002-02-09
实施日期：	2002-07-01
首发日期：
作废日期：
提出单位：	中国铁路部通信信号总公司二七通信工厂科研所
归口单位：	中国铁路部通信信号总公司二七通信工厂科研所
起草单位：	铁道部科学研究院通信信号研究所
起草人：	梅照佳、吕志东
出版社：	中国铁道出版社
出版日期：	2002-07-01
页数：	5页

适用范围

本标准规定了数字会议电话主席控制盘的技术要求。
本标准适用于数字会议电话主席控制盘的设计、生产和检验，也适用于科研及工程设计。

前言

没有内容

引用标准

没有内容

所属分类：通信广播通信设备电话通信设备

Product Code:SAE J4004
Title:Positioning the H-Point Design Tool - Seating Reference Point and Seat Track Length
Issuing Committee:Human Accom And Design Devices Stds Comm
Scope:This SAE Recommended Practice describes how to position and posture the H-point design tool (HPD) described in Appendix B, and how to establish the seating reference point (SgRP), design H-point travel path, and other key reference points that are used in the design and specification of both driver and passenger seat positions. This practice also provides a method for determining the length of the seat track for a driver seat that adjusts fore/aft. The seat track length is based on a desired level of driver accommodation, assuming a U.S. population containing an equal number of male and female drivers. The procedure can be used to establish driver seat track accommodation for new vehicle designs or to evaluate accommodation in existing vehicles. A general method for determining driver seat track length for any driver population (male and female stature distribution) at any selected accommodation percentile and gender mix is given in Appendix A. Application of this Recommended Practice is limited to Class A Vehicles (Passenger Cars, Multipurpose Passenger Vehicles, and Light Trucks) as defined in SAE J1100.A general method for determining driver seat track length for any driver population (male and female stature distribution) at any selected accommodation percentile and gender mix is given in Appendix A. Application of this Recommended Practice is limited to Class A Vehicles (Passenger Cars, Multipurpose Passenger Vehicles, and Light Trucks) as defined in SAE J1100.